9d7339f317
When a user explicitly disconnects after the session is open, cleanup its entry immediatelly. That ensures that a radius server will be notified sooner, while anyconnect clients which disconnect early (before session is open), remain unaffected. Resolves: #210 Signed-off-by: Nikos Mavrogiannopoulos <nmav@redhat.com>
3.8 KiB
Using Radius with ocserv
For radius support the radcli library is required. The minimum requirement is version 1.2.0. Alternatively the freeradius-client library can be used (1.1.7 is the minimum requirement), but not all radius features may be available.
radcli uses a configuration file to setup the server configuration. That is typically found at: /etc/radcli/radiusclient.conf and is best to copy the default installed as radiusclient-ocserv.conf and edit it accordingly.
The important options for ocserv usage are the following:
dictionary /etc/radcli/dictionary
servers /etc/radcli/servers
The dictionary should contain at least the attributes shown below, and the servers file should contain the radius server to use.
Note, that ocserv provides the 'NAS-Port' attribute to server, which corresponds to the worker process PID value. This PID value may change during accounting (because the client may be handled by a different process/port). To make the port change, not affect the radius server's unique ID, you must configure the server not to account NAS-Port. In freeradius servers for example you have to remove the NAS-Port attribute from the acct_unique section.
Ocserv configuration
For authentication the following line should be enabled.
auth = "radius[config=/etc/radcli/radiusclient.conf,groupconfig=true]"
Check the ocserv manpage for the meaning of the various options such as groupconfig.
To enable accounting, use
acct = "radius[config=/etc/radcli/radiusclient.conf]"
and modify the following option to the time (in seconds), that accounting information should be reported.
stats-report-time = 360
That value will be overridden by Acct-Interim-Interval if sent by the server.
Note that the accounting session is reported as terminated as soon as
possible when the user disconnects explicitly. When the disconnection
is due to timeout or other network reasons, the users have their connection
remain valid until the cookie-timeout value expires.
Dictionary
Ocserv supports the following radious attributes.
# Standard attributes
ATTRIBUTE User-Name 1 string
ATTRIBUTE Password 2 string
ATTRIBUTE NAS-Port 5 integer
ATTRIBUTE Framed-Protocol 7 integer
ATTRIBUTE NAS-Identifier 32 string
ATTRIBUTE Acct-Input-Octets 42 integer
ATTRIBUTE Acct-Output-Octets 43 integer
ATTRIBUTE Acct-Session-Id 44 string
ATTRIBUTE Acct-Input-Gigawords 52 integer
ATTRIBUTE Acct-Output-Gigawords 53 integer
ATTRIBUTE Acct-Interim-Interval 85 integer
ATTRIBUTE Connect-Info 77 string
###########################
# IPv4 attributes #
###########################
# sets local IPv4 address in link:
ATTRIBUTE NAS-IP-Address 4 ipaddr
# sets remote IPv4 address in link:
ATTRIBUTE Framed-IP-Address 8 ipaddr
ATTRIBUTE Framed-IP-Netmask 9 ipaddr
# sets routes (quite a kludge as it requires to have
# a CIDR string)
ATTRIBUTE Framed-Route 22 string
# Sets group name using format "OU=group1;group2"
# Note that this works only when groupconfig is set to
# true, and if the groups sent by the server are made known
# to ocserv, via the select-group variable.
ATTRIBUTE Class 25 string
# sets DNS servers
VENDOR Microsoft 311
BEGIN-VENDOR Microsoft
ATTRIBUTE MS-Primary-DNS-Server 28 ipaddr
ATTRIBUTE MS-Secondary-DNS-Server 29 ipaddr
END-VENDOR Microsoft
############################
# IPv6 attributes #
############################
# sets local IPv6 address in link:
ATTRIBUTE NAS-IPv6-Address 95 string
# sets remote IPv6 subnet in link:
ATTRIBUTE Delegated-IPv6-Prefix 123 ipv6prefix
# sets remote IPv6 address in link:
ATTRIBUTE Framed-IPv6-Address 168 ipv6addr
# sets DNS servers
ATTRIBUTE DNS-Server-IPv6-Address 169 ipv6addr
# Sets IPv6 routes
ATTRIBUTE Framed-IPv6-Prefix 97 ipv6prefix
ATTRIBUTE Route-IPv6-Information 170 ipv6prefix